Inspection and Test Plan for Method Statement: Mobile Crane Positioning, Outrigger Mat Configuration, and Ground Bearing Verification
AI-assisted inspection and test plan connected to a method statement, with PDF and Excel export.
More than a static template
Unlike a downloadable Word or PDF template, this ITP is an AI-assisted editable starting point directly connected to its method statement. Every inspection activity, hold point, and acceptance criterion is structured and ready to adapt to your project.
- AI-assisted customization — Tailor inspection activities and acceptance criteria to your specific project scope.
- Linked method statement — This ITP is connected to the corresponding method statement describing the work sequence.
- Multiple export formats — Download as a formatted PDF or editable Excel spreadsheet.
- Editable starting point, not a final document — Review and verify all content against your project specifications and standards before use.
What you can customize
When you save this ITP to your account, every inspection row becomes editable. You can add, remove, or modify:
- Inspection activity — Description of what is being inspected.
- Inspection type — Hold point (H), Witness point (W), Review (R), or Monitor (M).
- Responsibility — Contractor, subcontractor, engineer, or client.
- Frequency — How often the inspection occurs.
- Acceptance criteria — Referenced standard or specification requirement.
- Records — Forms, test reports, or checklists required as evidence.
Why this ITP is used
To control critical quality and safety points that prevent crane overturning and utility strikes through measurable inspections and tests.
Who uses this inspection and test plan
Appointed Person, Temporary Works Engineer, Geotechnical Engineer, Lifting Supervisor, Crane Operator, QA/QC, HSE.
When this ITP is prepared and submitted
Before crane arrival (planning), during set-up and levelling, prior to first lift (test), and during operations monitoring.
Who receives or approves this ITP
Client/Engineer/Principal Contractor [Verify]
Inspection scope
Design reviews, material inspections, platform testing, set-up inspection, levelling/function checks, preload/settlement monitoring, and test lift witness.
Typical hold, witness, and review points
Hold: Lift Plan/TWD approval; Set-up prior to preload; Test lift. Witness: Platform QA tests; Levelling/function checks.
Typical inspection records
Approved plans and calcs, permits, material certs, test reports, checklists, settlement logs, photos, close-out report.
Important approval note
This ITP is an AI-assisted editable starting point, not a pre-approved document. Before use on any project, all inspection activities, hold points, and acceptance criteria must be reviewed and approved by the relevant parties (superintendent, principal contractor, or client representative) in accordance with your contract and project quality plan.
Always verify acceptance criteria against your applicable drawings, specifications, and regulatory requirements. Hold points must be confirmed with the relevant authority before work proceeds past that point.
Inspection and test plan
| Activity | Inspection / Test | Acceptance Criteria | Responsibility | Record |
|---|---|---|---|---|
| Lift Plan and calculations approval | Design/Calc Review | Approved Lift Plan; Mat/ground calc signed by AP/TWE | AP; TWE | Approved Plan; Calc Sheets |
| Utility detection and permit | GPR/CAT survey | Permit-to-Dig/Avoidance issued; services marked on ground | Utility Coordinator; HSE | Survey Report; Permit |
| Platform construction/verification | Density/CBR/LWD | 95% MDD; CBR/LWD per TWD; level and slope within limits [Verify] | Geo Eng.; QA/QC | QA Test Reports; Inspection Sheet |
| Mat material inspection | Visual; cert check | Correct grade/spec; fit for use; no damage beyond limits | QA/QC | Material Inspection Report; Certs |
| Mat installation and crane positioning | Set-up inspection | Mats positioned per plan; pad centring; no point packing; exclusion zones set | Supervisor | Set-up Checklist; Photos |
| Levelling and function tests | Inclinometer; LMI/ATB tests | Level within ±0.5°; LMI/ATB operational; wind alarm set | Operator; Supervisor | Function Test Sheet; Level Record |
| Staged preload/settlement check | Settlement measure | Immediate settlement ≤ 10 mm per leg; differential ≤ 10 mm; re-level if required [Verify] | Supervisor; QA/QC | Settlement Log |
| Initial test lift | Partial load test | Stable response; no progressive settlement; communications effective | Supervisor; AP (Witness) | Test Lift Record |
| Operations monitoring | Routine checks | Wind within limits; level maintained; exclusion zones enforced | Operator; Supervisor | Operator Log; Daily Checklist |
| Demobilisation and reinstatement | Final inspection | No residual hazards; ground reinstated; all records closed | Supervisor; QA/QC | Close-out Report; Photos |
This table is a read-only public reference. Download the PDF or Excel version, or customize this ITP to edit it for your project.
Frequently asked questions
Related method statement
This Inspection and Test Plan is associated with the Method Statement: Mobile Crane Positioning, Outrigger Mat Configuration, and Ground Bearing Verification method statement, which describes the step-by-step construction sequence, resources, materials, equipment, safety controls, and environmental controls for this activity.
View the Method Statement: Mobile Crane Positioning, Outrigger Mat Configuration, and Ground Bearing Verification method statement →Continue with related inspection, method statement, article, and checklist resources.
