Inspection and Test Plan for Method Statement: Installation of Final Sanitary Ware Fixtures (WCs, Wash Basins, Bidets, Showers, Urinals)
AI-assisted inspection and test plan connected to a method statement, with PDF and Excel export.
More than a static template
Unlike a downloadable Word or PDF template, this ITP is an AI-assisted editable starting point directly connected to its method statement. Every inspection activity, hold point, and acceptance criterion is structured and ready to adapt to your project.
- AI-assisted customization — Tailor inspection activities and acceptance criteria to your specific project scope.
- Linked method statement — This ITP is connected to the corresponding method statement describing the work sequence.
- Multiple export formats — Download as a formatted PDF or editable Excel spreadsheet.
- Editable starting point, not a final document — Review and verify all content against your project specifications and standards before use.
What you can customize
When you save this ITP to your account, every inspection row becomes editable. You can add, remove, or modify:
- Inspection activity — Description of what is being inspected.
- Inspection type — Hold point (H), Witness point (W), Review (R), or Monitor (M).
- Responsibility — Contractor, subcontractor, engineer, or client.
- Frequency — How often the inspection occurs.
- Acceptance criteria — Referenced standard or specification requirement.
- Records — Forms, test reports, or checklists required as evidence.
Why this ITP is used
To ensure each fixture is installed to specification, safe, watertight, and functional before handover.
Who uses this inspection and test plan
QA/QC inspectors, site engineers, plumbing foremen, and the Consultant/Employer’s Representative.
When this ITP is prepared and submitted
Applied from material receipt through installation and final testing prior to area handover.
Who receives or approves this ITP
Consultant/Engineer for review and approval.
Inspection scope
Materials, set-out, anchors/brackets, fixture mounting, connections, sealing, and functional testing.
Typical hold, witness, and review points
Hold: anchor/bracket installation before mounting. Witness: final functional and leak tests.
Typical inspection records
MIRs, IRs, checklists, torque logs, photos, test sheets, as-built markups.
Important approval note
This ITP is an AI-assisted editable starting point, not a pre-approved document. Before use on any project, all inspection activities, hold points, and acceptance criteria must be reviewed and approved by the relevant parties (superintendent, principal contractor, or client representative) in accordance with your contract and project quality plan.
Always verify acceptance criteria against your applicable drawings, specifications, and regulatory requirements. Hold points must be confirmed with the relevant authority before work proceeds past that point.
Inspection and test plan
| Activity | Inspection / Test | Acceptance Criteria | Responsibility | Record |
|---|---|---|---|---|
| Material receipt and verification | Check models, finishes, certifications (WRAS/KIWA/NSF), damages | Conforms to approved submittal; no damage | QA/QC + Storekeeper | MIR, delivery notes, photos |
| Area readiness and permits | Verify finishes, waterproofing sign-off, isolation, permits | Area safe and ready; permits valid | Foreman + HSE | Pre-start checklist, PTW |
| Set-out verification | Heights, clearances, centerlines vs drawings | Heights ±5 mm; centerline ±3 mm | Engineer + QA/QC | Survey record/as-built |
| Anchor hole drilling and substrate check (HOLD) | Confirm scan results, hole diameter/depth/edge distance | Per ETA/manufacturer; dust-free holes | QA/QC + Engineer | IR (Hold) with photos |
| Bracket/carrier/frame installation | Level/plumb, torque on fixings | Level/plumb ±2 mm; torque per TDS | QA/QC + Foreman | In-process checklist |
| Fixture mounting (basins, WCs, bidets, urinals) | Alignment, stability, seating, gasket placement | Stable; no rocking; alignment within tolerances | QA/QC + Foreman | IR with photos |
| Connection of isolation valves and flexible hoses | Thread engagement, torque, no kinks, bend radius | ≥3 thread turns; torque per TDS; radius per manufacturer | QA/QC + Plumber | Torque log, checklist |
| Trap and waste installation | Washer seating, trap seal depth, waste fall | Seal ≥50 mm; slope 1:40–1:60 | QA/QC + Plumber | Checklist |
| Silicone jointing | Joint width/continuity; adhesion; curing | Uniform bead 5–10 mm; no voids; cure per TDS | QA/QC + Finisher | Photos |
| Functional and leak testing (WITNESS) | 10-min leak observation; flow/flush tests; thermostatic setpoint | No leaks; flow within spec; WC passes flush; mixer setpoint per spec | QA/QC + Consultant | IR (Witness), test sheets |
| Final protection and handover | Protection installed; signage; area clean | Protection intact; zero snags outstanding | Foreman + QA/QC | Handover checklist |
This table is a read-only public reference. Download the PDF or Excel version, or customize this ITP to edit it for your project.
Frequently asked questions
Related method statement
This Inspection and Test Plan is associated with the Method Statement: Installation of Final Sanitary Ware Fixtures (WCs, Wash Basins, Bidets, Showers, Urinals) method statement, which describes the step-by-step construction sequence, resources, materials, equipment, safety controls, and environmental controls for this activity.
View the Method Statement: Installation of Final Sanitary Ware Fixtures (WCs, Wash Basins, Bidets, Showers, Urinals) method statement →