Inspection and Test Plan for Method Statement: Gypsum Board Partition Installation
AI-assisted inspection and test plan connected to a method statement, with PDF and Excel export.
More than a static template
Unlike a downloadable Word or PDF template, this ITP is an AI-assisted editable starting point directly connected to its method statement. Every inspection activity, hold point, and acceptance criterion is structured and ready to adapt to your project.
- AI-assisted customization — Tailor inspection activities and acceptance criteria to your specific project scope.
- Linked method statement — This ITP is connected to the corresponding method statement describing the work sequence.
- Multiple export formats — Download as a formatted PDF or editable Excel spreadsheet.
- Editable starting point, not a final document — Review and verify all content against your project specifications and standards before use.
What you can customize
When you save this ITP to your account, every inspection row becomes editable. You can add, remove, or modify:
- Inspection activity — Description of what is being inspected.
- Inspection type — Hold point (H), Witness point (W), Review (R), or Monitor (M).
- Responsibility — Contractor, subcontractor, engineer, or client.
- Frequency — How often the inspection occurs.
- Acceptance criteria — Referenced standard or specification requirement.
- Records — Forms, test reports, or checklists required as evidence.
Why this ITP is used
To ensure partition systems are installed to specified quality, fire/acoustic performance, and tolerances with documented compliance.
Who uses this inspection and test plan
QA/QC engineers, site engineers, subcontractors, and the Consultant/Employer’s Representative.
When this ITP is prepared and submitted
From material delivery through setting out, framing, boarding, finishing, to pre-paint inspection and handover.
Who receives or approves this ITP
Consultant/Employer’s Representative
Inspection scope
Materials, setting out, substrate/drilling permits, tracks and studs, openings, boarding, services, insulation, fire/acoustic seals, finishing, and final inspection.
Typical hold, witness, and review points
H: Insulation placement; fire/acoustic seals; head-of-wall details. W: Setting out; first-side boarding; finishing; pre-paint inspection.
Typical inspection records
Material certificates, checklists, anchor logs, firestop reports, photo records, NCRs/closing, pre-paint sign-offs.
Important approval note
This ITP is an AI-assisted editable starting point, not a pre-approved document. Before use on any project, all inspection activities, hold points, and acceptance criteria must be reviewed and approved by the relevant parties (superintendent, principal contractor, or client representative) in accordance with your contract and project quality plan.
Always verify acceptance criteria against your applicable drawings, specifications, and regulatory requirements. Hold points must be confirmed with the relevant authority before work proceeds past that point.
Inspection and test plan
| Activity | Inspection / Test | Acceptance Criteria | Responsibility | Record |
|---|---|---|---|---|
| Material delivery and storage | Check labels, certificates, damage, moisture protection | Materials per approved submittals; boards dry/flat; studs within gauge tolerance. | QA/QC Engineer / Storekeeper | Material inspection report; delivery dockets |
| Setting out verification | Measure against drawings | Lines within ±5 mm to grid; openings located within ±3 mm. | Site Engineer / Consultant (W) | Setting-out check sheet |
| Substrate scan and drilling permit | Review scan map and permit | Permit approved; no-drill zones identified. | HSE / Site Engineer | Permit-to-drill; scan records |
| Floor track installation | Anchor spacing/edge distance; gasket continuity | Anchors ≤600 mm c/c; edge distance per manufacturer; straightness ≤3 mm in 2 m. | QA/QC Engineer / Consultant (W) | Track installation inspection |
| Head track/deflection detail | Gap and slotted track compliance; listing reference | Movement gap per design; continuous track; no fixings breaching deflection slot. | QA/QC Engineer / Consultant (W) | Head-of-wall inspection record |
| Stud erection and openings | Spacing, plumb, reinforcement at doors | Studs at 400/600 mm c/c ±3 mm; plumb ≤3 mm in 2 m; openings within ±2 mm. | QA/QC Engineer | Stud check sheet; photos |
| First-side boarding | Screw spacing/depth; perimeter gap; board orientation | Edges ≤200 mm; field ≤300 mm; edge distance ≥10 mm; floor gap 10 mm. | QA/QC Engineer / Consultant (W) | First-side checklist |
| MEP rough-in and framing | Box locations, offsets, penetration framing | Back-to-back boxes offset ≥300 mm or use rated/acoustic boxes; framed penetrations. | MEP Coordinator / QA/QC Engineer | MEP rough-in inspection |
| Acoustic insulation placement (HP) | Continuity/fit | Full-height, tight fit; density/thickness per spec. | QA/QC Engineer / Consultant (H) | Insulation checklist; photos |
| Fire/acoustic perimeter and penetration seals (HP) | Verify listed systems, seal depth/width, materials | As per UL/ETA listing; continuous beads; identification tags where required. | Firestop Specialist / Consultant (H) | Firestop inspection report; photos |
| Second-side boarding | Screw spacing/depth; joint staggering; deflection zone | Stagger ≥400 mm; no fixings to structure in deflection gap; spacing per spec. | QA/QC Engineer | Second-side checklist |
| Joint treatment and trims | Tape embedment; coat count; bead alignment | Level 4 finish unless noted; no ridges/voids; screws concealed. | QA/QC Engineer / Consultant (W) | Finishing inspection sheet |
| Surface flatness and plumb | 2 m straightedge and laser | Deviation ≤3 mm in 2 m; overall ≤5 mm in 3 m. | QA/QC Engineer | Flatness/plumb record |
| Pre-paint final inspection (W) | Visual and touch; lighting check | Ready for primer; no damage; seals intact and continuous at edges. | QA/QC Engineer / Consultant (W) | Pre-paint inspection report |
This table is a read-only public reference. Download the PDF or Excel version, or customize this ITP to edit it for your project.
Frequently asked questions
Related method statement
This Inspection and Test Plan is associated with the Method Statement: Gypsum Board Partition Installation method statement, which describes the step-by-step construction sequence, resources, materials, equipment, safety controls, and environmental controls for this activity.
View the Method Statement: Gypsum Board Partition Installation method statement →Continue with related inspection, method statement, article, and checklist resources.
